This is the ultimate tool for CCTV installers, This unit can check Video output test, Pan Tilt & Zoom testing, presets, speed, UTP cable test, Video signal generation, Green, white, black & blue screen and RS485 data test etc 2.4 Specification Model CCTV Tester Video Test Signal Mode NTSC/PAL automatically suitable Display 2.5 inch LCD screen,960 x 240 resolution Video Input 1 channel BNC Video Output 1 channel BNC PTZ Controlling Communication RS232 and RS485 Protocol Pelco D, P; Samsung, Panasonic or customer need. Baud Rate 2400,4800,9600,19200 Other Function Signal Generating Output 1 channel video signal for testing monitor UTP Cable Test Test UTP cable connection state and display in the screen RS485 Data Test Test the RS485 data sent from controlling device Operation English OSD menu Power Power Adapter DC9V---12V Battery 2 pcs 18490 standard batteries 3.6V,capacity 2800mAh Rechargeable 5 hours recharging time, work for 5 hours Low Consumption Sleeping mode, display battery power state Other Parameters Work Temperature -30oC---+70oC Work Humidity 30%-90% Dimension 170mm x 99mm x 48mm 3? Operation Introduction 3.1 Power and battery A. The power slide switch is located at the side of the tester. Turn the power slide switch on to power on the tester, to press the Power more than 3 seconds to make it turn into sleeping mode. B. Press the Power more than 3 seconds to turn on the tester after it turning to sleeping mode. C. Press the Power less than 1 second to shut off the OSD menu. D. Turn the power slide switch off to power off the tester. E. The batteries should be plugged in over 5 hours for full charge, when charged the Charge Indicating LED will on. F. After full charging, the Charge Indicating LED light will glitter and the charging work can stop automatically. G. The charged batteries can operate for 5 hours or more. H. When the battery indicator in system information menu shows 25 (the situation number includes 100, 90, 75, 50, 25), please recharge it for use. I. The tester can be used when it is being charged. 3.2 Video test A. Connect the output terminal of video output system to the video input BNC of tester, turn on the tester, the video can be display on the screen. B. Connect the video output BNC of tester to the video input of other display device, it can display the video signal generated by the tester or looped by tester. 3.3 PTZ test A. Connection Connect the tester with the PTZ camera as the picture shows. When the tester is on, it will show the PTZ test menu as follows: B. Operation setup Press Set to start the setup operation and switch between the 1st line and the 2nd line in menu. Press Left and Right to switch the optional item in the same line. Press Up and Down to change and select the parameter in each optional item. Press Enter to confirm the setup operation. Press Return to finish the setup operation. C. PTZ controlling When connect to the PTZ camera, the video can be displayed in the screen, after setup the protocol, baud rate and the address correctly, user can control the PTZ camera in the below method: Press Up/Down/Left/Right to pan tilt to control the camera. Press Open/Close to control the iris. Press Far/Near to adjust the focus manually. Press Wide/Tele to zoom in/out the camera lens. 3.4 System information menu A. Press Mode to switch to the system information menu as follows: B. Press Set to start the setup operation. C. Press Up/Down to select the optional items (just available for IDLE TIME and BUZZER). D. Press Left/Right to change the optional information. 3.5 UTP cable test A. Connect the tester to the UTP cable tester as the picture shows: B. Press Mode to switch to video UTP cable test menu. C. Press Set to start the test, UTP cable information will be displayed in the screen. D. User can estimate the UTP cable connection situation from the information. 3.6 Video generating A. Connect the tester to the displayer device as the picture shows: B. Press Mode to switch to video generating menu as follows: C. Operation setup Press the Mode to switch to the video generating mode Press Set to switch the video generating signal: Green, White, Black and Blue. Press Tele to send the generated video signal to the display device. Press Wide to recall the generated video signal. Press Return to finish the video generating operation. 3.7 RS485 data test A. Connect the tester to the controlling device as the picture shows: B. Press Mode to switch to RS485 data test menu as follows: C. Press Set to start the setup of baud rate. D. Press Up/Down to select the baud rate to be same as the controlling device used. E. Make the controlling device transfer the RS485 data to the tester, the hexadecimal signal data will displayed in the screen as follows, engineer can analyze the data to know if the controlling device work with the correct protocol. 4? Warranty 4.1 Warranty items Since the delivery day: 1) Exchanging service within 7 days from the receiving day, we responsible for the freight charge (battery exchanging service within 90 days from the receiving day). 2) Repairing service within 2 years, change accessories and repair for free, customers should responsible for the freight charge (repairing service don't include battery). 3) We provide whole life repairing service for our products with proper charge, customers should responsible for the freight charge. 4.2 Warranty exception We provide repairing service with proper charge, customers responsible for the freight charge 1) Damage caused by abuse, unreasonable use, mistreatment, or neglect. 2) Damage caused by modification or repair not authorized by our company, working in hostile environments, or natural disaster. 3) Damage caused by improper or improperly used packaging, or other devices work in the same system. 4.3 Complemented items 1) Company is not responsible for other assurance and other derivative from capital loss: The product and the user guides are not assured for particular users and some special purpose of use. 2) If the products returning for exchanging was damaged, modified or miss accessory, we will charge the proper payment. 3) If the components are no longer produced during the warranty-limited period, company will make a decision to replace similar products at no charge. 4) Don't offer exchanging service for special design products by customers.